Aantar POS
Install the store server on a PC
Install the Aantar POS Store Server on the Windows PC in the back office; it runs as a Windows service and starts with the computer.
Where: Start menu ▸ Aantar POS Store Server set-up page
On a store with two or more lanes, the store server usually runs on a Windows PC in the back office. You install it once. It then runs as a Windows service: it starts with the computer, with nobody signed in.
Before you start
- A Windows 10 or 11 PC (64-bit) that stays on all day and is not one of the tills.
- The PC is on the shop network by cable, with a fixed address reserved for it in the router.
- In Windows, the shop network is set as Private, not Public.
- The installer
Aantar POSStoreServer-<version>-setup.exe, from Aantar One Inc. or your reseller. - Your Aantar POS key file (
.aantarkey), if you have one. You can also give the key later on the set-up page. - Windows rights to install programs (an administrator account).
Steps
- Run
Aantar POSStoreServer-<version>-setup.exeas an administrator. - Data folder: keep the folder it proposes (
C:\ProgramData\Aantar Books\Host) unless you have a reason to change it. It must be on this PC's own disk, never a network drive. Uninstalling keeps this folder. - Server settings:
- Admin password (optional) and Confirm the admin password: the server's own password, at least 8 characters. It protects the set-up page. You may leave both empty; the set-up page then asks for it the first time you open it on this PC.
- Port (TCP; the tills connect here): keep 47810.
- Server name shown on the tills: a name the cashiers will recognize, for example
Back office server.
- Licence: choose the
.aantarkeyfile, or paste the key. You may leave it empty and give it on the set-up page. - Your Aantar account (optional): a Link code from your Aantar portal links the server to your account. Leave it empty to link it later. See Link a store server to your account.
- Let the installer finish. It opens the Windows firewall for the store server (TCP 47810 and UDP 47811, on Private networks only) and starts the service.
- On the last page, leave Open the set-up page now (make the company and pair the tills) ticked and finish. The set-up page opens in the browser.
- The browser warns that the connection is not private. That is expected: the server makes its own certificate. Choose Advanced, then continue to localhost.
- Carry on with The set-up page and the store server's licence.
Important: Write the admin password down and keep it in the store's sealed envelope, away from the PC. Without it nobody can pair a new till or change the company on the server.
Tip: The set-up page is also in the Start menu: Aantar POS Store Server set-up page. Its address on the server PC is
https://localhost:47810/setup.
Check that it runs
Once you are signed in on the set-up page, Server status confirms that the store server runs: it shows the Server name, the Version, the Licence, the Address tills type and the Certificate fingerprint. Write down two of its lines for the tills:
- Address tills type: the address each till uses to reach the server.
- Certificate fingerprint: the groups of letters and digits each till compares before it pairs.
What was installed
- The service Aantar POS Store Server (service name
Aantar BooksHost), automatic start, restarting itself after a failure. - The data folder, holding the store's company file, the list of paired tills, the server's certificate and its logs. Back this folder up. The server also backs the store up by itself: see Automatic backups.
If something goes wrong
- A till cannot find the server: check that Windows has the shop network as Private, that the till is on the same network (not a guest Wi-Fi), and that the service is running (Windows Services ▸ Aantar POS Store Server).
- The set-up page does not open: the service may still be starting. Wait a minute and open the Start menu shortcut again.
- The tills lost the server after the router restarted: the server's address changed. Reserve a fixed address for it in the router.
Related articles
Something unclear or out of date? Write to support@aantar.com and name this page.